Thursday, November 21, 2024

Backlights. Open, Identify and Replace

  VW Touran 1T Backlights how to OIR (Open, Identify and Replace)


  • Open. As soon as you receive the warning in your dash that one of your light bulb is out, you will have to change that light bulb. In this specific case we will change the positioning light on the right side. For this you need to do the following: Open the trunk, and remove the plastic cover that is on top of the light unit using a flat-head screwdriver and gently pry in the 3 sections shown in the pictures. first on the top, then in the middle and then at the bottom.





After carefully opening the cover we need to remove the 2 TORX screws that are holding the light unit in place. One up, the other down








        After removing the screws, we need to push out to the side the unit. It is being held by 2 supports from witch it will simply pop out. Push with care because you don't want to drop it break the cables. With one hand push from the middle of the unit and with the other hold the unit.










       After removing the unit, on the back of it we have the connector. This is a little stubborn to come out but it will come in the end. Simply press the small clips on the connector and in the same time pull out while keeping pressed the clips, A little juggle, pull and voila, its out.







    Next we have to remove the light bulb cover. To do this we have to press the 2 clips on the side pull gently out and then the top connector the same in a gently manor to pull out. Exactly like in the pictures bellow.








  • Identify. Well like all incandescent light bulbs the wire inside has to be intact. In my case, the wire was broken. 














  • Replace. After identifying the defective bulb, we have to replace it. All the bulbs from this panel are being removed by simply pressing and turning either to the right, or to the left and then pull out. After removal we insert another the same way we removed it. Put the new bulb inside, press it, twist and let go. Very easy!






After we are ready with the replacement we have to put everything back just as we took it all apart. Same steps but backwards. 
In the closing i want to give you also the types of bulbs we need for the Touran and Golf since I have for both. Success!!!!







12-V-Light bulb for Typ Leistung
High beam low beam H7U 55 W
Low beam, xenon headlights H7U 55 W

D2S 35 W
Fog lights H11 55 W
Stand light w 5 W
Front turn signal light py 21 w
Front turn signal, Xenon headlights H2 WLL1> 21 w
Rear Turn Signal (GOLF) H6 WLL 6 W
Rear turn signals (TOURAN) py 21 w
Tail lights (GOLF) p 21 w
Tail lights (TOURAN) R 5 W
Brake-Lights p 21 w
Rear fog light p 21 w
Reversing light p 21 w
License plate lights c 5 W
Lounger lights (GOLF) w 6 W
Entry lights (TOURAN) c 5 W
Reading lights, front w 5 W
Ceiling lamp, front c 10 W
Ceiling lamp, in the back w 2> 5 W
Trunk light c 10 W
Glove box light (GOLF) w 5w
Glove box light (TOURAN) c 3 W
Floor lamp w 5w




Adjusting door on a Touran 1T

    Adjusting door on a Touran 1T  it is the most easiest thing to do as a repair. As you open the door you want to adjust, you will see the hinge that has 2 screws. 1 up and 1 down. Slightly unscrew the 2 bolts just enaugh for the hinge to move. if you need more closure, simply slide to the inside of the car. If you want aperture slide the hinge to the outside. Simple! After selecting the necessary adjustment, tighten back the screws! This is valid for both sides! Succes!




BEFORE ADJUSTMENT







AFTER ADJUSTMENT







😉

All the info in replacing the bulb in your ashtray's orange ring

Replacing the bulb in your ashtray's orange ring


  • UPDATE! The lights from the light switch of my car were not staying on after switching on the headlights, they went out every time after ~5 seconds, either was the light of my hazard button. But now that I have replaced the light bulb of the ashtray, the lights now stay on! So it is a very easy fix!!!!

  • To replace the light bulb we have to take apart a lot of things and it is very upsetting that otherwise we cannot see if the light bulb is defective or not. For this we are going to start by opening the ashtray and remove the 2 screw covers. This can be done with a small flat head screwdriver. It has to be done gently so that we don't damage the plastics, either from the covers, or from the ashtray. 











  • Next, we unscrew the 2 screws (that in the pictures I have already taken out) and pull out the ashtray unit with force. In the back of the unit there are some clips that hold it in place so we have to unhook the unit. Repetitive short strong pulls will take it out. 
  • With the ashtray out, we have to remove the light bulb case unit. First remove the securing clip that is on the light bulb unit. With the small flat head screwdriver gently pry of the clip.





                    

  • Now we can remove the light bulb case unit. Again using the small flat head screwdriver, pry out the unit. Gently, slight force is enough, be careful not to break anything.










With the light bulb case unit out we have to take out the light. Finally! We use the small head screw driver to open the casing and to finally remove the bulb itself. be careful because this requires some force and since is a small unit, very small unit the screw driver can slip and hurt our fingers! Again, be careful and work with love and dedication! You will succeed!













  •  With this we have to replace the bulb and then in reverse order we putt everything back! Simple! Have fun! Succes



The type of bulb used is:


Type  T5 glass base matt
Voltage: 12 V
Power: 1.2W
Length max. 20 mm
diameter max. 5 mm

  




Lights from the light switch problem

If the lights from the lights switch, or the light from the hazard button  don't stay on after turning on the lights  it may be becaus...